How To Maintain Automatic Granite Cutting Machine
1, if there is a gap between the uneven brick to be cut and the bottom tile, the appropriate thickness of paper can be added between the two to avoid the generation of corner
2, replace the appropriate saw blade: the larger the diameter of the saw blade, the better the emery content, the better the coarse sand type than fine sand, the higher the motor speed, the better. It is recommended to use a Baotao Φ130*20 saw blade.
3, automatic granite cutting machine operation specifications to properly reduce the cutting speed, it is recommended to 1 m/min. The two hands will push the cutting machine table plate forward with uniform force for cutting. When the contact point of the cutting piece is 10 ~ 20㎜ with the tail of the brick, the advancing speed must be slowed down to control the collapse Angle. In the process of pushing, do not press the brick with both hands. Hold the brick against the positioning rod as shown in the following figure.
Automatic Granite Cutting Machine Note
1. It is recommended to use a cutting machine with a rotating speed of more than 1 m/min.
2. The bottom of the brick should be flat; Add water to cool when cutting; The direction is backward cutting (and the cutting piece rotation direction) technique should be straight, not swing from side to side, slow and uniform cutting; In the process of cutting, the cutting machine can not press the brick to cut, and it should be appropriate to lift the cutting machine to cut along the force path
3.automatic granite cutting machine operation specifications and safety matters:
In the cutting process, we must pay attention to the position of the saw blade and control the speed of cutting products, and do a good job of self-protection measures to prevent being cut;
The broken ballast of the product must be washed with water in the process of cutting. It is strictly prohibited to clean it directly by hand.
When cutting, the hand and the cutting piece must maintain more than 10㎜ distance, in order to prevent the cutting piece hurt the hand.
Automatic Granite Cutting Machine Precautions
In the process of cutting, properly control the cutting speed, the next knife should be slow, the middle can be faster, the knife must be slowly closed to prevent the lack of Angle.
automatic granite cutting machine. Automatic granite cutting machine
Different brick products are cut with different types of saw blades. For example, polishing brick should use peak type, microcrystalline stone and enamel brick should use fine sand type saw blade to prevent tooth breakage glaze. Antique brick can be properly cut with a longer saw blade meters to reduce the cutting cost.
automatic granite cutting machine will inevitably encounter harsh conditions and complex environment in its work. Once there is a problem, it is cumbersome and difficult to find out the problem, which often makes people at a loss. It also involves system operation, system integrity, adjustment quality, environmental pollution and other problems. Therefore, the reasonable use of operation is very important, so let Xiaobian for you to explain the maintenance of automatic granite cutting machine common sense:
Fourteen Head Automatic Granite Cutting Machine
1, cleaning pipe to extend the life
Welding slag, rust, solidified slag, iron wire, cloth, etc. in the pipeline cause blockage or jam in the throttling orifice and the guiding part of automatic granite cutting machine to break the valve core, which often occurs in the new operation system and the initial operation after overhaul. This is the most common failure. In this case, it must be removed for cleaning, remove slag, such as sealing surface damage should also be ground; At the same time, open the bottom plug to wash away the slag, and wash the pipeline. Before operation, let the regulator fully open, let the medium flow for a period of time before normal operation.
2, increase the opening to extend the life
When starting to use ceramic regulator, try to work on the maximum opening, such as 80%. In this way, the initial impurities in the pipeline erosion, wear and other damage occurs outside the damaged part of the valve spool, after removing the impurities in the pipeline, and then adjust the opening of the valve to the normal opening slightly larger place, with the fluid damage to the valve spool, flow increase, automatic granite cutting machine should reduce the opening accordingly, so as to continuously destroy and gradually close, so as to make full use of the whole spool until the root and sealing surface of the spool are damaged and cannot be used.
3, increase the caliber to improve the life
4. Transfer failure location to improve life
Transfer the serious damage to the secondary location to protect the sealing surface and throttle surface of the valve core seat. Usually ceramic ball valve erosion is the most serious, fluid speed is the fastest place below the fluid inlet, for now ceramic ball valve three-piece structure, can be used to reverse the ball core, so that a ball core can be used four times at the inlet, so that the life of the valve is extended 4 times.
5, change the valve structure to improve the life
